Laboratory Equipments

Zonotech ZL-TF High Temperature Tube Furnace
Model BL-TF1150 BL-TF1450
Maximum Temp. 1150°C 1450°C
Working Temp. 1100°C 1350°C
Temp. Accuracy ±1°C ±1°C
Heating Elements Kanthal - A1 wire, coil type with end connection, easily replaceable. Silicon carbide, coil type with end connection, easily replaceable.
Inner Chamber Ceramic Refractory/Board with heating elements placed on the top and bottom.
Insulation Ceramic Fibre Ceramic Fibre
Construction Tripple walled with air insulation on the outer side for minimal skin temp.
Body Made of mild steel duly powder coated.
Tube Material Alumina(Option-quartz)
Tube Size Inner Dia.=75 mm /Hot zone length=200 mm /overall length=600 mm ,Furnace with tube of different dia Hot zone length and overall length can also be made as per customer requirment.
Gas Purging Ends of the tube have Almuniam couplers with cooling attachment for purging of gases
Power control SSR Unit Scr Unit(Phase Angle Thyristor)
Temp. Control Microprocessor based PID Digital set point controller.Dual display of set & actual temp.with soft touch keys with thermocouple break protection and cold junction compensation.CE mark to meet EMC regulation
Sensor Cr/Al Pt/Pt - Rh 13%
Safety Over current and short circuit protection.Thermocouple break alarm.High temp alarm.
Power Supply 220 volts,single phase AC supply.
Zonotech ZF-14P 1400 High Temperature Muffle Furnace
Maximum Temp. 1400°C
working Temp. 1350°C
Temp. Accuracy ±1°C
Heating Elements Silicon carbide.Spiral type,with end connection eaisly replaceable.
Inner Chamber Creamic board with base plate of silicon carbide, with heating elements placed on the top.
Insulation Creamic fibre of zirconia grade.
Construction Tripple walled with air insulation on the outer side for minimal skin temp.
Body Made of mild steel duly powder coated.
Door Parallel action hinged type insulated with creamic fibre and has a viewing cap.
Power Control Scr Unit(Phase Angle Thyristor)
Temp. Control Microprocessor based PID Digital set point controller.Dual display of set & actual temp.with soft touch keys with thermocouple break protection and cold junction compensation.CE mark to meet EMC regulation
Sensor Pt/Pt - Rh 13%
Safety Cut off of power to the heating elements when the door is opened.Over current and short circuit protection Thermocouple break alarm.High temp alarm.
Power Supply 220 volts,single phase AC supply.

 

Zonotech BL-RS Mini Rotary Shake
PLOATFORM SIZE 300 x 300mm (12" x 12" inch) U
MOTION Orbital (Horizontal Plane)
SPEED MODEL : BLRS-300 Fix speed of 180 RPM
MODEL : BLRS-300V Variable speed, max. 180 RPM
TIMER 0 -15 min Electro-mechanical Timer

 

Zonotech BL-RS Rocker Shaker
PLOATFORM SIZE 300 x 300mm (12" x 12" inch)
MOTION Rocking (End to End)
SPEED Fix Speed of 20 - 30 RPM
TIMER 0 -60 min Electro - mechanical Timer

 

Zonotech BL-RS Wrist Action Shaker
Construction Cast Iron Body
Motion Wrist action
Speed Variable speed max.300 RPM
Flasks a) 4 Flasks or b)8 flasks
Flask Capacity Max. 500 ml.(Concinal flasks)

 

Zonotech BL-RS Universal Shaking Machine
Construction Mild steel, Powder coated body with shaking tray
Motion Reciprocating(To-Fro action)
Tray Mild steel tray with slotted side to accomodate 12mm rubber covered steel rods with threaded ends (adjustable).Can accomodate flasks rack bottels of different sizes.
Tray Size  50*30*8 cm (l*w*D)
Speed MODEL:BL-RS 70 fix speed of 180 RPM
MODEL:BL-RS 70DC Variable speed max.180 RPM
Timer 0-60 electro mechanical timer.

 

Zonotech BL-RS Swing Roller Mixer
Construction Mild steel body, with rubber rollers, for mixing blood samples, . medicines, reagents
Motion Simultaneous rolling & swinging action
Speed Fix Speed of 50 - 60 RPM
Botlles Upto 100 ml.
Rollers 30 MM X 300 MM (Dia. X Length)
a) 3 Rollers
b) 5 Rollers

 

Zonotech ZL-RS Vortex Mixer
Construction mild steel powder coated body
Motion Vigorous agitation(cyclone motion)
Speed Variable speed with touch feature.
Cup Neoprene rubber cup for various tube size.

 

Zonotech BL-SP Spin Coating Unit

We are engaged in offering a superior quality range of Industrial Paints & Thinners. These are procured from reliable vendors who have a reputation for offering quality products. Our precisely formulated range is widely used as a thinning agent for a multitude of oil based paints and is appreciated for superior quality.
 

Technical Specification

Stainless Steel bowl (removable)

Size : 6 inch dia, with acrylic cove

Speed : 500-6000 RPM

Microprocessor Speed Control

Digital Speed Indicator Vacuum

Dial gauge Solenoid Vacuum release switch

Digital Timer 1 to 999 sec.

Vacuum chuck to hold substrate

Vacuum chuck to hold substrate from 1" to 4" inch

Lid cover of acrylic with interlock safety switch

Frame : Epoxy coated MS and Aluminum

Facility for interlocking with Vacuum Pump

Tubing for Vacuum

Gas Purging Attachment

To operate on 230V + 10%, 1 phase 50 Hz AC only.

Zonotech BL-BOD Incubators & Cold Cabinet

TECHNICAL SPECIFICATION


Double walled inside Stainless Steel / Aluminium, outside made of mild steel Duly painted with Insulation of 75mm

Chamber with shelf supports, allowing wide range of shelf positions & spacing. Supplied with removable perforated Stainless Steel/Aluminium shelves.

Full view inner Acrylic door allows inspection of sample without disturbing temp. , ofworking chamber.

Outerdouble walled metal doorwith MAGNETIC GASKET LOCK & KEY.

Door operated illumination lamp.

Cabinet mounted on Castorwheels. forease of movement.

Temp. is controlled by Microprocessor Digital Temp. lndicatorcum controller. Air circulating system is provided by F.H. Motors with fan which keeps uniform temp.through outthe chamber.

In B.O.D. Cooling Incubator a quite running sealed. CFC FREE Compressor (ISI marked) with all its protective devices along with a fan cooled condensing unit are placed below the working chamber.

Control Panel is provided at the top of cabinet with three nos. indicator for Main, Heating & Cooling,Voltmeter etc.
 

ILLUMINATION:(OPTIONAL)


Chamber illumination with 3 nos. fluorescent tubes of 60 cm length (3Ocm length in 4cu. ft.) placed vertically along the black wall. Separate ON/OFF switch for tubes and min. temp. can be obtained from 10 to 50°C when all theTubes are ON. With Timer 0-24 hours for regulating cyclic illumination condition fixed on the top ofthechamber.
 

COLD CABINET

These cabinet are designed for storing of culture, specimen & regents in laboratories.

Inside made of stainless steel with adjustable shelves.

Frost free chamber

Full view front glass door.

Microprocessor digital temp.Indicator cum controller with audio visual alarm for varition in temp.

Zonotech BL-TF1700 Flocculator

We have emerged as one of the leading manufacturers and suppliers of wide variety of Pipe Fluccolator. This product is manufactured by our experts using high quality raw material that is sourced from the reliable vendors of the industry. The offered product is available in various specifications to meet the varied requirements of our clients. Further, this product is highly appreciated by our clients for its quality attributes like brilliant performance, compact design, easy operations, less maintenance and high durability.

Zonotech Laboratory Stirrers
Model BLS-100 BLS-120 BLS-130 BLS-140 BLS-140H

STIRRING

DIA mm 6 6 8 12 12
LENGTH mm 250 250 350 450 450
IMPELLER PITCHED BLADE PITCHED BLADE PITCHED BLADE PITCHED BLADE × 2 PITCHED BLADE × 2
MOTOR H.P 1/20 1/20 1/8 1/4 1/2

SPEED (RPM)

MIN. 800 800 800 900 900
MAX. 4000 4000 4000 5000 6000

STIRRING CAPACITY

FLUID WATER WATER WATER WATER WATER
MAX. VOLUME 7LT. 7LT. 20LT. 30LT. 50LT.
SPEED REGULATOR TRANSFO
-RMER TYPE
RHEOSTAT TRANSFO
-RMER TYPE
TRANSFO
-RMER TYPE
TRANSFO
-RMER TYPE

 

Zonotech Tissue Homogenizer
MOTOR 1/20 HP AC/DC motor, 4000 RPM.
SPEED CONTROL Auto transformer speed regulator / Rheostat
SHAFT HOLDER Chuck, to accommodate shaft of diff. sizes
GRINDER Teflon grinding pristle glass homogenizing cup of 30 ml.

 

Zonotech Soil Stirrers
MOTOR 1/8 HP AC/DC motor, with stand
SPEED CONTROL Rheostat / electronic speed regulator
SHAFT HOLDER Tapered Aluminium shaft with brass blade
GRINDER Brass cup with wire supports.

 

Zonotech Muffle Furnace

TECHNICAL SPECIFICATION


LightWeight with ceramic Fiber wool insulation (instead of Brick insulation).

Outer casting is made of double walled thick P.C.R.C. sheet, finished with attractive powdercoating.

Element are made of KANTHAL "A-1 " wire in coil form.

Insulation by Zirconia cerewool. which avoids loss of energy, this arrangement also assures the most uniform distribution of heat.

A viewing cap is also provided onthe door.

Temperature controlled by "Microprocessor Digital Indicator cum Controller" fitted in thefront ofthe Furnace.

To work on 220/230 Volts or440/440 Volts A.C. 3 Phase supply.

Model Inner Size Rating
  WxHxD Rating
MF - 12D 100 x 100 x 225 mm 14. x 4" x 9") 2.5 K.W.
  125x 125 x 250 mm (5" x 5" x 10") 3.° KW.
Max. Temp : 1200°C. 150 x 150 x 300 mm (6" x 6" x 12") 4.0 KW
Working Temp. : 1150°C. 200 x 200 x 300 mm 18" x 8" x 12") 5.0 K.W.
  200 x 200 x 450 mm 10 x 8" x 18°) 8.0 K.W.
  300 x 300 x 300 mm 112" x 12" x12") 6.0 K.W.
  300 x 300 x 450 mm 112" x 208") 9.0 K.W.
  300 x 300 x 600 mm (12" 0 12" 024") 12.0 K.W.

 

Zonotech Orbital Shaker

TECHNICAL SPECIFICATION


These Heavy Duty Shakers with latest technology have been recently developed to give better flexibility, ease of operation and performance, than everbefore.

The unit has base assembly fabricated from heavy mild steel sections.The simple and sturdy design makes the units suitable for continuous operation.

Compact counter balanced drive mechanism ensuring high stability and reliability even in continuous operation &uneven load distribution.

Stepless Microprocessor frequency control ensures gentle start and maintains preset speed.

Brushless induction drive motor practically maintenance free.

Variable speed from 30RPM to 300RPM ±1RPM.

Digital display of RPM.

Automatic restart at preset speed in case of powerfailure.

Temp. control by Microprocessor PlDcontroller(optional).
 

OPTIONAL

 

  1. Clamps for Holding Conical Flask 100 ml., 250 ml., 500 ml., 1000 ml., 2000 ml.

  2. Mechanical Timer 0-120 min, for timing the shaking operation.

  3. Digital Timer of 99 hrs., for timing the shaking operation.

  4. Chamber illumination with florescent tube (1 No.)

(for Model BRS-100 H & 50H)

  1. Chamber illumination with U.V. Tube (1 No.)

(for Model BRS-100 H & 50H)

  1. Cyclic timer for illumination control. (for Model BRS-100 H & 50H}

Voltage Stabalizer for above.  

MODEL BRS-100V BRS-100H BRS-100H BRS-50V
Shaking Speed Variable microprocessor controlled
Speed Indication Digital
Speed Range 30-300 Rpm ±1Rpm
Orbital dia. 19 mm
Platform Size 42×42 cm. 35×35 cm.
Shaking tray Universal platform to accomodate interchangeable clamps of assorted sizes for different capacity of clonical flasks.
Temp Range   Ambient+5°c-60°c   
Temp Accuracy   ±0.1-0.4°c      
Temp Control   Microprocessor PID controlled    
Power Supply 220 volts,50 hz,AC single phase supply.

 

Zonotech Rotary Vacuum Evaporator

SPECIAL FEATURES

 

SAFE :

Non sparking motor reduces risk of fire.
 

VERSATILE :

Variable speed for a variety of uses.
 

UP & DOWN MOVEMENT:

Manual / Motorised by Push of a button.
 

SPEED METER:

Electronic Digital Speed Meter. (Optional)
 

WATER BATH :

Digital Temperature Controlled Stainless Steel Water Bath.
 

CHEMICALLY INERT:

Glass Parts/Flasks, No contimation of metal parts.
 

LARGE OR SMALL VOLUMES:

Continuous feed of solvent into evaporator flask lets you handle large volumes.
 

STANDARDIZED :

All glass parts easily replaceable.

Use rotary vacuum evaporators for vacuum distillation of solvents at high or low temperatures, for vaccum drying of powders and solids, for evaporating heat-sensitive compounds, for degassing and for multiple extractions.

The pear-shaped evaporating flask is connected to a rotating glass steam duct. which runs through the drive units and into the stationary condenser. An easily inserted vacuum seal, is located in the condenser mouth.Vapors pass from the evaporator flask through the steam duct and into the condenser where they are condensed and collected in the receiving flask. An inlet feed tube at the upperend of the condenser is used for continuous feeding of liquid and to aerate the evaporator.

The rotating action of the evaporator increases the evaporation and insures even heating in the models with Microprocessor Digital Controlled Stainless Steel Boiling Water Bath.The solution to be concentrated is placed in the flasks, which rotates, mixing the solution and moving the liquid continuously upward.This action provides a large evaporating surface and in the water bath models. prevents over heating on the hot innerwall of the flask. By careful control of the speed of rotation and of the heat input, forming and bumping can be minimized. Evaporation with flask rotation speed 30-180 RPM.The flask can be removed easily by moving the motor assembly UP / DOWN by the manual / motorized mechanism by the Push of the button.

METREX Rotary Vacuum Evaporators are supplied with one liter evaporator and receiving flasks, a long steam duct, a condenser, an inlet feed tube, clamps a drive unit and a 3-wire rod with Electronic Digital Speed meter (optional). to show the speed of Evaporator Max. speed 180 RPM
 

OPTIONAL

(1) ASPIRATORVACUUM PUMP

Comprise fo a 10 Lt. Water tank and circulating pump. Built in feed water drain and overflow make it easy to change water. The water tank opens to the side of the unit for easy filling. Vacuum ports are suitable for 3/8" OD hose. Max.Vacuum = 700mm Hg./27 inch Hg. on dial gauge
 

(2) DIAPHRAGM TYPE VACUUM PUMP

Max.vacuum :27 inch. Hg.
Suitable to operate on 220 volts 50 cy. AC only.

Zonotech Vacuum Oven

Microprocessor based Vacuum ovens are accurate and reliable. Proportional Integral Derivative (PID) temperature control system continuously monitors rate of temp. change, eliminating temperature overshootand undershot.

Heaters are embedded on the periphery of the chamber. providing excellent temperature uniformity and quick heating times.

The gap between the inner and outer wall is filled with special grade glass wool insulation.

Outer body is made of mild steel finished in attractive powdercoating and innerchamberof stainless steel, with 2 Nos. wire mesh trays.

Moulded. Joint less door gasket and knob ensure a tight seal.

Fitted with bourden type dial gauge of range 0-30" Hg.

Gas valve allows evacuation & venting.

The front door has heat resistant glass window. for allowing viewing ofsamples.

(# WITH OUT VACUUM PUMP)

Model        Temp Range        Temp Accuracy

BV-1            50°c to 130°c              ±1°c

BV-2            50°c to 250°c              ±1°c

BV-3            50°c to 300°c              ±1°c

Zonotech Hot Air oven Model - ZOP250

TECHNICAL SPECIFICATION

Temperature Control PID Microprocessor Control with Dual Display of Set & Actual Temp.
Construction Double Walled, Inside made of Stainless Steel 304 & outer made of Mild Steel Duly Powder Coated
Door Hinged insulated door fitted with heat resistant gasket
Heating Element Kanthal Wire
Insulation High Quality Mineral Wool
Air Circulation Motorised Blower, for Uniformity of Temp.
Trays Wire Mesh Nickle Plated (2/3 No.)
Timer (Optional) 99 Hr. with built in Alarm system
Power Supply 220V, 5OHz Single Phase AC

 

Model        Temp Range        Temp Accuracy        
ZV-13          50°c to 130°c              ±1°c                   

ZV-25          50°c to 250°c              ±1°c

ZV-30           50°c to 300°c              ±1°c

Zonotech Full Visibility Bath

TECHNICAL SPECIFICATION



Useful for Crystal Growth Studies. for determination of Kinematic Viscosity and other laboratory applications requiring precise control of temp. need of visibility.

The bath maintains precise temp. for long duration of time.

Microprocessor PID temp. controller gives accuracy of temp. upto ±0.1°c / ±0.01°c (Optional)

The bath is rectangularin shape.Insidetank made of Stainless steel304. Ontwo sides toughed glass windowis provided forfullvisibility of samples. Stirrer is cushioned with vibration absorbing rubber pads.

Fluorescent light is provided forviewing of the samples (optional)

Viscometertray is provided for holding 2/4/8 viscometer (optional)

ZONOTECH SEED GERMINATOR MODEL - ZSG13

TECHNICAL SPECIFICATION


Designed for conducting various experiments on variety of seeds underdifferent parameters oftemperature. humidity etc.

It is of double wall construction. Inner chamber is made of I Q- Aluminium/Stainless Steel 304 & outer cabinet is made of MS sheet, duly pretreated & finished with epoxy powder paint.

Insulation is provided between inner chamber & outer body to minimize heat loss.

The shelf position oftrays is adjustable.

Stainless Steel water reservoir at the bottom provides 90% to 95% RH fixed humidity (not adjustable).

Temperature from 5°C to 5O°±1°C is controlled by . Microprocessor Digital temperature indicatorcum controller.

A inner transparent acrylic door is provided to view the germination of seed inside the chamber without opening the door, thus notemperature/humidityloss.

Air circulation ensure uniform temperature & humidity inside the chamber.

A heater is provided fortemperature control inside the chamber. The CFC free compressor is placed belowthe chamber.

Control panel is fitted with voltmeter, indicators, Microprocessor DigitalTemp.Controller, switches etc.

Zonotech Split Type Furnace

We have on offer for our esteemed customers a comprehensive range of Split Type Furnaces. Products offered in this range can be availed in different diameters and other technical specifications.

The Split Type Furnace that we provide with has been made in the best possible manner that consists of the quality which is up to the mark. These furnaces are well made under the superior guidance of professionals who are known in the market. We adhere to all the norms set by the market. These furnaces are majorly used in laboratories to carry on with the experiments. They are availed by our clients in a cost effective rate.

Features

Well tested

Quality oriented

Cost effective

 

Zonotech Orbital Incubator Shaker

TECHNICAL SPECIFICATION


Orbital shaking incubators are specially designed to have combined advantage of a closely controlled incubation/storage - temperatures with orbital shaking.

Constructed of double walls, the exterior is made of Mild Steel Sheet and lnteriorof Stainless Steel (304).

The plexiglass inner door makes it possible to inspect specimen without disturbingthe temperature.

Outer Door is made of Toughened Glass window in Frame with lock & Key.

Air Circulating fan creates positive air flow through the incubator, and maintain uniform temp.

With 2 nos. perforated Stainless Steel adjustable trays. Incubator Shaker (Refrigerated Model) incorporates hermetically sealed lSl marked CFC Free compressor housed below the incubatorto provide temperature below ambient.

The control Panel comprises of Microprocessor Based PID Digital Temp. Controller, Digital RPM Indicator, Speed Regulator.
 

Driver :

Triple Eccentric Counter balanced drive with permanently lubricated ball bearing ensures high stability and reliability.

Drive Motor :

Brushless Induction Drive Motor, maintenance free.

Automatic Restart :

Automatic restart at preset speed in case of Power Failure.

Speed Control :

Microprocessor Based.

Safety :

Auto cut off in case of overshoot of temp, short circuit protection by MCB/Overload Glass Fuse.

MODEL BO-250 NON-
REFRIGERATED
BO-250 C REFRIGERATE BO-100 NON-
REFRIGERATED
BO-100 C REFRIGERATED
Working Capacity 250 It. 250 It. 165 lt. 165 lt.
Temp Range Ambient+ 5A°C
to 60A°C
5A°C to 60A°C Ambient+ 5A°C
to 60A°C
5A°C to 60A°C
Temp. Control PID Microprocessor Based
Temp. Accuracy 0.1A°C - 0.4A°C
Shaking Speed Variable Microprocessor Controlled
Speed Range 30 to 300 rpm. 11 rpm.
Orbital Dia 19 mm.

 

Zonotech Cryostat Circulating Bath

Cryostat baths are extensively manufactured for research work at desired temperature with perfect accuracy.

These Constant Temperature Baths are designed to carry out research work at desired temperatures with a high degree of accuracy. These are compact table top units fabricated out of sheet steel with a stainless Steel chamber having capacity of 12 litres. Refrigeration is achieved by means of a hermetically sealed compressor. The temperature is controlled by a digital temperature controller-cum-indicator. Fine tuning of the heating system ensure high accuracy within a limit of +/-0.1 deg C. The unit can be operated continuously and are equipped with bottom discharge.

Zonotech Vertical Autoclave

High pressure, electrically heated vertical steam sterilizer is used for sterilization of surgical instruments, dressing material, linen, rubber, plastic material by means of saturated steam under pressure of 15 psi. Apart from health services it is also used in scientific research institutions and universities. Sturdy double walled construction with boiler/inner chamber made of stainless steel of 18 SWG sheet. Outer shell is made of mild steel finished with attractive enamel paint. The boiler and outer shell is provided with air insulation. Lid is made of mild steel plate with SS lining and is tightened by radial locking system with paddle lifting. Moulded, joint less gaskets are made of Neoprene rubber. Autoclaves are fitted with water level arrangements to indicate water position inside the boiler, pressure gauge, Air/steam release cock, spring loaded safety valve and Automatic Pressure switch which can be set at any selected point from 5 psi. to 20 psi ± 2 psi. and drain. ISI marked immersion type heating element heats the water and steam to desired temperature and pressure. Supplied complete with S.S. basket, cord and plug to work on 220 Volts, 50 cycles AC supply.
 

Model : ZA-101E (ECONOMY MODEL)


DoubleWall Construction, Inside made of Stainless Steel, Outer mild steel or S.S with S.S Basket.

RADIAL LOCKING SYSTEM (chrome plated) and paddle lifting, with water level arrangement.

Lid made of Mild Steel with S.S. Lining

Provided with built - in safety valve, pressure gauge, pressure release valve. With Automatic Pressure switch, pressure is adjustable form 5 to 20 psi i1 psi. Suitable to operate on 220V, single phase AC supply.
 

Model : ZA - 101 D (DELUXE MODEL)


Lid made of Stainless Steel. with S.S. Basket.

Inside & Outside made of Stainless Steel.

Triple Wall Vertical Autoclave Model - ZA-10D

The unit comprises of steam jacket electricity heated, inner chamber & lid made of stainless steel, works on phase V A/C 50 Hz supply fitted with automatic pressure control switch safety valve etc.
 

CHAMBER

The chamber is made of heavy gauge stainless steel, fitted with stainless steel lid with radial locking system , chamber is fitted with two safety valve of stainless steel, pressure gauge, water outlet valve and Air inlet valve, stainless steel eject valve.

Triple wall construction, all three wall inner, jacket, outer are made of stainless steel 304, with S.S Basket.

RADIAL LOCKING SYSTEM (chrome plated) and paddle lifting, with water level arrangement.

Lid made of Stainless Steel Plate

Provided with built - in safety valve, pressure gauge, pressure release valve. With Automatic Pressure switch, pressure is adjustable form 5 to 20 psi 11 psi. Suitable to operated on 220v, single phase AC supply.
 

INNER SIZE :

DIA (MM) 250 300 350 450 550
DEPTH (MM) 450 500 500 650 700

 

OPTIONAL


* Automatic Low water Level cut off

* Digital temp. Indicator

* Dial Type Analogue Temp. Gauge

* Mechanical Timer O-60 min.

* Digital Automatic Temp. Controller and Digital Timer (to sterilize the samples
   for set time after Temp. is achieved)

 

Zonotech Horizontal Autoclave Model -ZA10H

Triple walled with steam jacket and separate boiler. Inner chamber and steam jacket are made up of Heavy gauge S.S. Sheet with leak proof argon-arc welding.The sterilizer has single piece S.S Door. All the sterilizers are hydraulically tested to withstand 2.5 times the working pressure.

Mounted on tubular steel frame with ground leveling screwed flanges. The Outer jacket is wrapped with asbestos sheet or glass wool to minimize the heat losses due to radiation and is covered by polished Stainless steel sheet for that elegant appearance.
 

Model : ZA10H


Triple walled construction.

Inner chamber and jacket are made of high grade stainless steel 304 sheet. The outer body is made of thick stainless steel sheet.

The lid is made of thick stainless Steel plate WITH SAFETY LOCKING DEVICE. The boiler placed below the chamber is made of stainless steel with view glass and immersion heaters. with low water level cut off.

A multiport valve made of SS is installed forcontrolling the sterilization cycle. The pressure is adjustable from 5 to 20 psi i 1psi controlled by automatic pressure control switch.

Fitted with vacuum breaker, steam trap, dial type temp. gauge. The whole unit is mounted on a robusttubularstand made of MS duly painted. Suitable to operate on 440 V, 3 phase AC supply.

INNER SIZE :

DIA (MM) 400 500 550 400 500
DEPTH (MM) 600 900 750 1100 1200

 

Zonotech Deep Freezer

TECHNICAL SPEFICIATION


Deep Freezer designed for quick freezing & storing at low temperature.

Constructed double walled. Exterior is made of sheet steel powder coated while interior stainless steel 304

PUF INSULATION to minimise heat loss.

'lSl' marked hermetically sealed compressor, for CFC free refrigerant

Capillary controlled balanced hermetically sealed Refrigeration is most economically trouble free and Exceptionally quiet.

Fitted with Microprocessor Digital Temp. Indicator-cum-controller with Audi0VisuaI alarm, for deviation in temp.

Mounted on castorwheels for easy mobility.

MinimumTemp.= -20°C / -40°C (in AC Room)

TECHNICAL DATA

MODELS VOLUME
(LITRES)
INSIDE DIMENSIONS
W × D × H (CM)
MINIMUM TEMPERATURE RECOMMENDED VOLTAGE STABILISER

HORIZONTAL FREEZERS

ZZH-170 170 Ltrs. 60 × 4O × 70 -20°C 2 KVA
ZZH-17OX 170 Ltrs. 60 × 4O × 70 -40°C 2 KVA
ZZH-265 265 Ltrs. 95 × 40 ×× 70 -20°C 3 KVA
ZZH-265X 265 Ltrs. 95 × 40 ×× 70 -40°C 3 KVA
ZZH-425 425 Ltrs. 110 × 50 × 78 -20°C 4 KVA
ZZH-650 650 Ltrs. 167 × 50 × 78 -20°C 4 KVA

VERTICAL FREEZERS

ZZH-170 170 Ltrs. 50 × 43 × 85 -20°C 2 KVA
ZZH-17OX 170 Ltrs. 50 × 43 × 85 -40°C 2 KVA
ZZH-300 300 Ltrs. 58 × 50 × 99 -20°C 3 KVA
ZZH-300X 300 Ltrs. 58 × 50 × 99 -40°C 3 KVA

Supply :220 Volts, 50 Hz, single phase AC supply.

Zonotech Environmental & Stability Chamber

TECHNICAL SPECIFICATION

Model : BEC & BEH

These Environmental Test Chambers can satisfy a variety of environmental conditions. They are especially suitable for the simulation of fixed temperature and relative humidity values above freezing point. Used for seed testing, biological studies, forestry research work etc.
Constructed of double walls. the exterior is made of sheet steel, the interior of stainless steel 304.
Aflush fitting insulated doorhas leak proofgasket.
The shelf position oftrays is adjustable.
The rear chamber of the interior is fitted with a refrigeration evaporator (In Refrigerated Model), heater and powerful air circulating fan to create a positive airflowthrough the chamber.
A hermetically sealed ISI mark, CFC Free compressor below the chamber provides temperatures below ambient (In Refrigerated Model).
The same compartment houses a boiler with an immersion heater and water level controllerforcreating humidity.
Safety circuit which cuts of system and stops unit in case of malfunction of Controller. Audio-Visual alarm with cut outfor low water level.
The control panel comprises of ON/OFF switches. heat energy regulators, Microprocessor based Digital Temp. Indicator & Humidity lndicator-cum- controller (Direct display of Humidity in % RH), indicating lamps and protective fuses.
 

STABILITY CHAMBER

 

Model : BSC

Same as above but with-
The chambers have outer body of SS 304 (dull finish) and inner chamber of SS 316
Validation protocol for IQ, OQ, PQ as per ICH guidelines
 

OPTIONAL

* Chamber Illumination with Flurescent lights with 0-24 hr. cyclicTimer
* Chamber Illumination with UitraViolet Light.
* A Surge Tank of 100-150 Lt. Capacity, with automatic arrangement to fill the Humidity reservoir automatically when the level of water drops, thereby ensuring continuous unattended operation for2-3 days.

Model Volume (cu.ft.) Inner chamber H × w × D mm Trays Temp. Range & Accuracy(°c) Humidity Range & [%RH] Voltage Stabilizer
BEC-6 6 830×505×415 2 10°C-60°±0.5°C 40%-95%±3% to 5% 2 KVA
BEC-10 10 830× 505×550 2 10°C-60°±0.5°C 40%-95%±3% to 5% 2 KVA
BEC-12 12 900×650×580 3 10°C-60°±0.5°C 40%-95%±3% to 5% 3 KVA
BEC-15 15 900×700×650 3 10°C-60°±0.5°C 40%-95%±3% to 5% 4 KVA
BEC-30 30 1500×900×600 3 10°C-60°±0.5°C 40%-95%±3% to 5% 4 KVA
BEC-6 6 830×505×415 2 Ambient +5°C-60°±0.5°C Ambient-95%±3% ---
BEC-10 10 875×570×550 2 Ambient +5°C-60°±0.5°C Ambient-95%±3% ---
BEC-6 6 830×505×415 2 10°C-60°±0.5°C 40%-95%±3% to 5% 2 KVA
BEC-10 10 875×570×550 3 10°C-60°±0.5°C 40%-95%±3% to 5% 2 KVA
BEC-12 12 900×6500×580 3 10°C-60°±0.5°C 40%-95%±3% to 5% 2 KVA

 

Zonotech Laminar Air Flow & Fume Hood Model - ZLA100

HORIZONTAL /VERTICAL CABINET

The bench is made of thick ply board. and reinforced with teak wood where ever necessary.
All visible surface are laminated with white Decolam Lamination. The filter seat has rubber padding fora perfect rubberto rubbersealing. The panels are made of Perspex sheet duly framed in Anodized Aluminium frame with transparentdoor.
The worktable is also covered with satin finish stainless steel 304. At the suction end the unit is provided with washable pre-filters.The pre filters have an efficiency of 90% down to 1 O micron particle size.
At the Delivery end, the unit is provided with Super air H.E.P.A. Filters, comprising of non woven microfibre glass pleated media. The pleats are separated by corrugated aluminium foil separators. lntial pressure drop is i less then 25mm W.G. at rated flow D.O.P. efficiency is better then 99.97% down to 0.3 microns particle size. The H.E.P.A. filters are protected by a plastic grill.
The Blower assembly consists of a ‘A H.P. Electric Motor of "American Universal" or equivalent make. and balanced blowers. The unit is illuminated by Flourescent tube light & U.V. germicidal light (optional).
Fitted with static pressure manometor (acrylic body) and cock for gas. Designed to provide a work area confirming to class 100 of revised US ‘ Federal standards 209-B.

BIOSAFETY CABINET

In addition to the Vertical Laminar flow, it has a exhaust system with perforated Stainless Steel Table top.

WORK SPACE L×W×H ft. HEPA FILTER FTL UV LIGHT
2'x2'x2'ft. 2'x2'x6' 1×20W 1×15W
3'x2'x2'ft. 3'x2'x6' 1×20W 1×15W
4'x2'x2'ft. 4'x2'x6' 1×40W 1×30W
6'x2'x2'ft. 3'x2'x6'-2 no. 2×40W 2×30W
8'x2'x2'ft. 4'x2'x6'-2 no. 2×40W 2×30W

The above cabinets can be made with body of Stainless Steel 304.

FUME HOOD Model - ZFH-2

Chamber made of hard board, Epoxy coated or with fire proof asbestos lining from inside with strong blower exhaust system.
Flourescent Light arrangement and sliding sash door with toughened glass window in wooden / aluminium frame with counterweights.
Power plug with socket provided inside the Chamber.
Work table covered with ceramic tiles for chemical resistance.
Stainless Steel/Ceramic sink is fitted on the side (optional).
The space beneath the work table is provided with storage compartments (optional).
The balanced PVC blower with stainless steel 316/ FRP acid resistant deck and PVC pipe duct and joints is fitted at the top.
To work on 220/230v AC 50Hz.

WORK SPACE L×W×H ft. EXHAUST DUCT Dia (inc) FTL
4'x2'x2'ft. 3 1×40W
6'x2'x2'ft. 4 1×40W
7'x2'x2'ft. 4 1×40W

 

Zonotech Water Bath Incubator Shaker

TECHNICAL SPECIFICATION

SHAKING MOTION : RECIPROCATING / ORBITAL

Water bath incubator shaker is of sturdy construction with outer body made of mild steel sheet duly powder coated and inner chamber made of stainless steel grade 304.
The gap between the inner and outer chamber is filled with effective insulation.
Temp. is controlled by Microprocessor PID Temp. controller, with dual display of temp.(process&set value).
A variable speed motor is fitted to provide shaking of the tray. the speed of the motor can be varied through a stepless electronic regulatorfitted in the panel.
The shaking tray moves on four wheels / balls (Reciprocating). Eccentric Cam (Orbital).
With Digital RPM Indicator (optional)
in Refrigerated Model, Temp. below ambient is achieve by hermetically sealed CFC FREE compressor (lSl Mark) placed below the water bath with other refrigeration accessories.
For above ambient temp. stainless steel immersion type heating elements are provided inside the bath.
The bath is provide with a stainless steel pyramidical shaped lid and a drainplug. Supplied complete with one shaking rack of 100ml conical flasks.
 

OPTIONAL

Shaking Racks for MMI - 100 (1) & (2)

16 No. x 25ml. Conical Flask
12 No. x 50ml. Conical Flask
9 No. x 100ml. Conical Flask
5 No. x 250ml. Conical Flask
4 No. x 500ml. Conical Flask
2 No. x 1000ml. Conical Flask
20 No. x 25mm dia test tube

Shaking Racks for MMI - 100 (3)

MMI - 100C & MMO - 200
20 No. x 25ml. Conical Flask
16 No. x 50ml. Conical Flask
12 No. x 100ml. Conical Flask
9 No. x 250ml. Conical Flask
6 No. x 500ml. Conical Flask
4 No. x 1000ml. Conical Flask
30 No. x 25mm dia test tube

MODEL SHAKING TRAY (L×W×D) mm Temp. Range and Accuracy RPM SHAKING TYPE
BWB-100 1) 275×275× 75 Ambient + 5°C-100°C±O.1°C 30-150 RECIPROCATING
  275×275× 150      
  400×300× 150      
BWB-100C 400×300× 150 10°C - 90°C ± 0.1°C 30-150 RECIPROCATING
BZO-200 400×300× 250 Ambient + 5°C-100°C±O.1°C 30-200 ORBITAL
BZO-200C 400×300× 250 10°C - 90°C ± 0.1°C 30-200 ORBITAL

 

Zonotech Titurating Machine

ELECTRIC PORCELAIN PESTLE MORTAR (TITURATING MACHINE)


ELECTRIC PORCELAIN PESTLE MORTAR glazed out side but with inside grinding surface unglazed as is the grinding end of Pestle is used extensively for mixing and grinding of Homeopathic medicine, pigments, refractories, cosmetics, granules, chemicals, ceramics, Drugs manufacturers for unattended grinding material which are notgummy offibrous.
The Pestle Mortar is designed to meet the demand for a labour saving device, which would fill all the requirements for grinding and mixing of different manufacturers. The base is strong attractively finished upon which Mortar revolves.The pestle is held firmly in weighted Pestle head.
Arm of Pestle mechanism is hinged and moves to and fro in a pattern reaching al parts of mortar.
Built in Automatic Timer O/60 mts. "Holder" Switch is provided for continuous untimed operation.
The Scraper blade, scraper arm, and 4 no. tightening bolts & nuts are made of Stainless Steel 304.
Sample is shielded from AIR BORNE CONTAMINANTS BY transparent Perspex cover
After the material has been ground. the Pestle holder is raised and Plate holding the Motor is lifted off so that the contents can be entied and Mortar Brushed out or sterilized byflame.
Standard Equipment furnished with Scraper Arm, Scraper and one set of 250 MM dia Procelain Pestle Mortar with wire and plug and cord for 220 volts 50 cy. AC /440 Volt. 3 Phase AC Supply.
Model :BZG-102S
--do-- but3O0 MM dia(12") Procelain Pestle Mortar Model :BZG-102
--do-- but 400 MM dia(16") Porcelain Pestle Mortar Model : BZG-102L
 

ELECTRIC AGATE PESTLE MORTAR (TITURATING MACHINE)


Model : BZP-101
STANDARD EQUIPMENT furnished with scraper arm, scraper, detachable turn table of cast aluminium has adjustable post to hold 80 to 135 MM dia. of mortar and with one set of Agate Pestle Mortarof 87 MM Inner dia with a wire cord & plug for22O volts 50 Cy. AC only.
EXTRA ACCESSORIES
Metrex Agate Pestle & Mortar size 7.5 cms.,8.7cms.,1Ocms..11.2cms.,12.5cms. Are available.
‘The above models of Titurating Machines are also available with outer body of Stainless Steel 304,to satisfythe GMP requirement.
 

POTENIZER (BIG)


Metrex Potenizer electrical operated fitted with 1 HP foot mounted capacitor start motor having 30 RPM complete with arm and wooden carrierfor lifting the 6 no. amber bottle of 450ml. The suitably filled bottles fall at the height approx. 40cm on a base provided with cushion. Having and arrangement to stop after 10 stroke. Complete unit made of mild Steel nicely painted. Suitable for 220 volts. 5Ocy-AC/440 Volts. 3 Phase AC Supply.
* The above unit can also be provided with an extra wooden carrier to accommodate 100ml bottles.

Zonotech Lypholizer

Aesthetically designed cabinet gives a pleasant look. It is a free standing Castor mounted unit. It is supplied with a powerful double stage vacuum pump.

Hermetically sealed compressor gives temperature upto -40°C (at ambient temp. 20°C)

Condenser trap is provided of stainless steel dished bottom for complete effluent removal.

Refrigerant coils made of copper are PUF insulated for maximum efficiency.

Temperature is adjustable upto - 40°C and is maintained automatically by Microprocessor digital temp. controller.

Vacuum drum having 22.8 cm dia and 25.4cm height is made up of non magnetic stainless steel with plexiglass top cover and incorporates 6/ 12 quick seal valves/ports for manifold drying.

Double stage vacuum pump with gas blast giving vacuum 1×10³ torron Mc-Ieod Gauge.

Suitable to work on 220V, 50 Hz AC supply.
 

Capacity :

3 liters for 6 tests, 5 liters for 12 tests

Lypholizers are generally the freeze dryers which are loaded in the controlled environment and then unloaded in the sterile environments. These Lypholizers are manufactured using accurate and exact chemicals and materials required for its manufacturing.

We make Ozone Friendly CFC/HCFC Free, all purpose lab. Model Freeze Dryer (Lyophilizer) 5 Ltrs. Cap. Floor standing model size (31” x 22” x 32” approx.) housed in a Super Structure Frame and S.S. working top, with removable side panels, mounted on swivel castors for easy mobility, Refrigeration coils (Imported copper) bonded out side the condenser (for no damage to Refrigeration line), Foamed-in-place Poly Urethane (PUF) Insulation helps ensure Temp. stability & energy efficiency, Full view acrylic see through lids, for condenser and drying manifold to observe the freeze drying process continuously, and control instruments i.e. Digital solid state Temp. Indicator LED for continuous display of temperature and electronic vacuum indicator for vacuum measurement.

Zonotech Automatic Potentizer

TECHNICAL SPECIFICATION

 

MATERIAL OF CONSTRUCTION :

Microprocessor Logic Controlled
Outer Body & frame of mild steel.
All parts coming directly in to the contact of
Drug solution made of SS 316.
Dosing pipe material - Silicon /Teflon
 

CYCLE TIME :

For a complete Dosing / Dynamization / Evacuation,
machine will take 12 sec. (approx)
lt gives a speed of around 5 cycles per min (approx)
 

DOSING :

1. Solvent will be fed in to 10ml / 15ml Bottle through injection
made of SS 316. Dosing Accuracy will be close to 1 3%
2. Dose Volume can be adjusted from 5ml. to 15 ml. as per
the requirement.
3. Dosing time : 1.5 sec to 2 sec. per cycle
 

DYNAMIZATION :

1. For Dynamization - vertical vibration
2.Vibration speed 60 RPM. Dilution is shaken for 10 strokes in 10 Sec.
3. Vibration time is 10 sec. per cycle.
4. The bottle rests on a spongy surface, so that each stoke ends in a Jerk.
5. Stroke height is between 10 to 15 cm.
 

EVACUATION :

1. Evacuation will be through air Compressor with dry filtered air.
2. Evacuation time 0.5-1 sec/cycle.
3. Amount of drug solution to be left inside the bottle can be adjusted as desired.
 

GENERAL FEATURES:

1. Digital electronic counters for indicating numbers of cycles completed (6 Digit counter)
2. Machine will completely stop automatically at the prefixed cycles number.
3. The machine accurately shuts down at pre-set numbers of performance / dilution. In case of power failure it
retains the data in memory and restarts the dilution from the stage it was shut off and continue to further stage.
 

POWER INPUT :

440 Volts. Three Phase AC supply.

ZONOTECH MUFFLE FURNACE 1200 C, MODEL - ZF-12P
Maximum Temp. 1200°C
working Temp. 1100°C
Temp. Accuracy ±1°C
Heating Elements Silicon carbide.Spiral type,with end connection eaisly replaceable.
Inner Chamber Creamic board with base plate of silicon carbide, with heating elements placed on the top.
Insulation Creamic fibre of zirconia grade.
Construction Tripple walled with air insulation on the outer side for minimal skin temp.
Body Made of mild steel duly powder coated.
Door Parallel action hinged type insulated with creamic fibre and has a viewing cap.
Power Control Scr Unit(Phase Angle Thyristor)
Temp. Control Microprocessor based PID Digital set point controller.Dual display of set & actual temp.with soft touch keys with thermocouple break protection and cold junction compensation.CE mark to meet EMC regulation
Sensor Pt/Pt - Rh 13%
Safety Cut off of power to the heating elements when the door is opened.Over current and short circuit protection Thermocouple break alarm.High temp alarm.
Power Supply 220 volts,single phase AC supply.
ZONOTECH INCUBATOR MODEL - ZI-250

TECHNICAL SPECIFICATION

Construction Double Walled, Inside made of Stainless Steel 304 & outer made of Mild Steel Duly Powder Coated
Door Hinged insulated door fitted with heat resistant gasket
Heating Element Kanthal Wire
Insulation High Quality Mineral Wool
Air Circulation Motorised Blower, for Uniformity of Temp.
Trays Wire Mesh Nickle Plated (2/3 No.)
Timer (Optional) 99 Hr. with built in Alarm system
Power Supply 220V, 5OHz Single Phase AC
ZONOTECH WATER BATH MODEL: ZWB-30

Model : ZWB-30

Doble walled chamber made of stainless steel 304 and outer wall made of thick mild steel sheet dully finished in attrective powder coating paint. The gape between outer and inner walls is filled with special grade glass wool insulation.

The concentric rings are of S.S. 304, The Tempreture is controlled by reputed make cappilary thermostate from 5 degree C above room temp. to 90 degree C.

Suitable to operate on 220V, 1pH, 50Hz,AC supply

W     x    H     x    D
300x250x100mm with 6 holes of 75mm dia
350x400x100mm with 12 holes of 75mm dia

 

ZONOTECH B.O.D. COOLING INCUBATOR MODEL - ZBI50

Model - ZBI50

Technical Specification : 

Doble walled inside stainless steel 304 & outside made of mild steel duly powder coated. chamber with self support, allowing wide range of self positions & specing supplied with removable perforated stainless steel shelves. Full view inner crylic door allows inspection of simple without disterbing of temperature of working chamber. outer double walled metal door with magnetic gasket, Lock & Key. 

Door operated illumiation lamp, cabinet mounted on castor wheels, for ease of moment, Temp.controlled by microprocessor digital temp. indicator cum controller. Air circulating system is provided by F.H. motors with fan which keeps uniform temp. through out chamber. in B.O.D. cooling incubator A quite running shield, CFC free compressor (ISI maked) with all its protective devices along with a fan cooled condensing unit of placed below the working chamber. controll pannel is provided at the top of cabinet three Nos. indicator for main, Heating & cooling, volmeter etc.


 TECHNICAL DATA 

Model

Volume 

(Cu.ft)

Inner working space

H x W  x  D  (mm)

No. of Shelves

Temp. Range 

 

Recommended 

Voltage stablizer 

ZBI50A 4Cu.ft. 610x455x410mm        2                 

 5ºC to 60ºC   

  2KVA              
ZBI50B 6Cu.ft 830x505x415mm   3   5ºC to 60ºC         2KVA
ZBI50C 10Cu.ft 875x570x550mm   3   5ºC to 60ºC         3KVA
ZBI50D 12Cu.ft 900x650x580mm   3   5ºC to 60ºC         3KVA
ZBI50E 15Cu.ft 900x700x650mm   3    5ºC to 60ºC    3KVA

 

ZONOTECH PROGRAMMABLE MUFFLE FURNACE 900C Model - ZF-9P
Maximum Temp. 900°C
working Temp. 850°C
Temp. Accuracy ±1°C
Heating Elements Silicon carbide.Spiral type,with end connection eaisly replaceable.
Inner Chamber Creamic board with base plate of silicon carbide, with heating elements placed on the top.
Insulation Creamic fibre of zirconia grade.
Construction Tripple walled with air insulation on the outer side for minimal skin temp.
Body Made of mild steel duly powder coated.
Door Parallel action hinged type insulated with creamic fibre and has a viewing cap.
Power Control Scr Unit(Phase Angle Thyristor)
Temp. Control Microprocessor based PID Digital set point controller.Dual display of set & actual temp.with soft touch keys with thermocouple break protection and cold junction compensation.CE mark to meet EMC regulation
Sensor Pt/Pt - Rh 13%
Safety Cut off of power to the heating elements when the door is opened.Over current and short circuit protection Thermocouple break alarm.High temp alarm.
Power Supply 220 volts,single phase AC supply.
HIGH TEMPERATURE PROGRAMMABLE MUFFLE FURNACE 1400C MODEL -ZF14P
Maximum Temp. 1400°C
working Temp. 1300°C
Temp. Accuracy ±1°C
Heating Elements Silicon carbide.Spiral type,with end connection eaisly replaceable.
Inner Chamber Creamic board with base plate of silicon carbide, with heating elements placed on the top.
Insulation Creamic fibre of zirconia grade.
Construction Tripple walled with air insulation on the outer side for minimal skin temp.
Body Made of mild steel duly powder coated.
Door Parallel action hinged type insulated with creamic fibre and has a viewing cap.
Power Control Scr Unit(Phase Angle Thyristor)
Temp. Control Microprocessor based PID Digital set point controller.Dual display of set & actual temp.with soft touch keys with thermocouple break protection and cold junction compensation.CE mark to meet EMC regulation
Sensor Pt/Pt - Rh 13%
Safety Cut off of power to the heating elements when the door is opened.Over current and short circuit protection Thermocouple break alarm.High temp alarm.
Power Supply 220 volts,single phase AC supply.
Refrigerated Universal Centrifuge Model - ZRC-70

Refrigerated universal Centrifuge Brushless, 20000rpm, Premium Model

Digital premium brushless model Microprocessor based. Max Speed 20000rpm further speed depends upon rotor being used. Fitted with Microprocessor based LCD Pannel for 0-59 minutes countdown timer, digital rpm meter and programmable speed controller. Stand by temperature from -20 Degree C to room temperature is controlled by microprocessor based digital Temperature controller cum indicator. Working temperature from -8 Degree C

 

Rotor head For ZRC -70 can be selected from below mentioned.

  • Angle Rotor 12X1.5/2.0ml with adopters 0.5/0.2ml, Max. Speed 20000 RPM
  • Angle Rotor 24X1.5/2.0ml, Max. Speed 16000 RPM
  • Angle Rotor 8X15ml, Max. Speed 13000RPM
  • Angle Rotor 4X50ml, Max Speed 13000RPM
  • Angle Rotor 4X100ml, Max Speed 10000RPM

 

 

ZONOTECH DIGITAL HOT PLATE ZHP500

Minimum Temperature : 500C

Maximum Temperature : 5000C

Rectangular hot Plate heavy duty Ceramic coated Top

Fitted with Digital PID Temperature controller.

Size : 250X250mm

Supply completed with, instruction manual, cord & plug to work on 220 volts 50Hz A.C.